Well Pump Replacement
Reliable Water Restored
Has your well pump finally worn out, or is it struggling more every year? Our plumbers pull failed pumps and install new ones, inspecting the drop pipe, wiring and controls along the way.
Well Pump Replacement Done Carefully From Wellhead to Pump Depth
Well pumps don’t last forever. Sand and sediment wear impellers, minerals scale up internal parts and frequent cycling wears out motors. A pump nearing the end often shows warning signs: lower pressure than it used to deliver, longer run times to refill the tank, rising electric bills, tripping breakers or noisy operation on jet pumps. Eventually it stops entirely, often at the least convenient moment, leaving the household without water until it’s replaced.
Replacing a submersible pump means lifting the entire assembly out of the well, including the pump, motor, drop pipe and wiring, which can extend hundreds of feet. It takes the right equipment and care to avoid dropping anything into the well. Our well pump replacement service pulls the old pump, inspects every component that comes up, replaces what’s worn and installs a new pump sized for your well, then tests and disinfects the system.
Well Pump Replacement Services We Offer
We replace submersible and jet well pumps for homes, ranches and small businesses, upgrading drop pipe, wiring, check valves and controls when they’re worn and confirming the new pump suits your well’s current depth, yield and water level.
Submersible Replacement
Pull failed submersible pumps and install new units at correct depth.
Jet Pumps
Swap out worn above-ground jet pumps serving shallow or deeper wells.
Drop Pipe
Replace corroded steel or damaged plastic drop pipe during pump replacement.
Wiring Upgrades
Replace damaged or undersized submersible cable and failing waterproof splices.
Control Updates
Replace pressure switches, control boxes and check valves alongside pumps.
Constant Pressure
Upgrade to variable-speed pumps for steady household pressure during replacement.
What's Involved in Pulling and Replacing a Submersible Pump
First, power is shut off and the well cap is removed. The drop pipe is disconnected from the pitless adapter below ground, and the entire assembly is lifted out, section by section for steel pipe or as a continuous length for flexible pipe. Depending on depth and weight, this may require a pump hoist or truck-mounted equipment. Safety ropes and careful handling prevent the assembly from dropping into the well, which would create a costly retrieval problem.
As the assembly comes up, we inspect the drop pipe for corrosion or splits, the wire for abrasion and the check valves for wear. These parts are often replaced with the pump, since reusing worn components risks another pull soon after. The new pump is assembled with fresh splices, check valves and torque arrestors, lowered to the proper depth and reconnected at the pitless adapter, then tested for flow, pressure and electrical draw.
Why Well Owners Choose Our Pump Replacements
We confirm a pump has failed before pulling it, and we do the job right when it has. Our licensed and insured plumbers use proper lifting equipment and safety lines, inspect every component that comes out of the well and replace worn pipe, wire and valves instead of reusing them. We verify pump sizing against your well’s current conditions, test the new system thoroughly and disinfect the well before you drink the water.
Fast Service
Quick and Reliable Plumbing Services.
Qualified Team
Skilled and Certified Plumbers at Your Service.
Affordable Price
Competitive Quality Plumbing Solutions.
150+ Project Done
Our Track Record of Excellence.
Benefits of Professional Well Pump Replacement
Professional replacement restores reliable water pressure and flow to your home after a pump failure. Replacing worn drop pipe, wire and check valves at the same time prevents another costly pull soon after. Correct sizing and depth protect the new pump from running dry or cycling excessively. A modern pump can be more efficient, lowering electricity use. And proper disinfection ensures your water is safe after the well has been opened.
Well Pump Replacement in CA, TX and FL
We provide well pump replacement for rural homes, ranches and small businesses throughout California, Texas and Florida, including deep wells where specialized lifting equipment is required to pull pumps safely.
Upgrading Drop Pipe and Wiring During Replacement
When the pump comes out of the well, the drop pipe and wiring come with it. That makes replacement the ideal time to evaluate and upgrade them.
Older galvanized steel drop pipe corrodes, especially at threaded joints, and can leak or break. Many systems are upgraded to durable plastic or stainless steel pipe suited to the pump depth and weight. Leaks in drop pipe cause pressure loss and pump run time increases that are hard to diagnose.
Submersible wire can be abraded against the casing over time, and old splices can fail. Wire must also be sized for the motor and the depth to prevent voltage drop. Replacing worn wire and splices now costs far less than pulling the pump again a year later.
How Our Well Pump Replacement Works
We confirm the pump has failed through electrical and system testing, review your well’s depth and records and recommend a replacement pump.
You’ll receive pricing for the pump and any recommended pipe, wire or control upgrades. On replacement day, power is shut off, the well is opened and the old assembly is lifted out with appropriate equipment while we inspect each component carefully for wear and damage.
Fresh splices, check valves and torque arrestors go on the new unit before it’s lowered to the correct depth. Controls are connected, and we measure flow, pressure, amperage and cycling. After the well is disinfected and capped, a lab bacteria test is advised before anyone drinks the water.
Replace Your Worn-Out Well Pump
Pump failed or struggling to keep up? Our licensed plumbers handle well pump replacement with proper lifting equipment, quality components and full system testing.
Well Pump Replacement Questions Answered
When does a well pump need replacing?
Declining pressure, longer run times, rising electric bills, tripping breakers or no water after other causes are ruled out suggest replacement.
How long does replacement take?
Many replacements are completed in a day, depending on well depth, access and whether pipe, wire or controls are also replaced.
Should I replace the drop pipe too?
If it’s corroded, damaged or old galvanized steel, yes. Replacing it along with the pump avoids another costly pull later.
Can I upgrade to a constant pressure pump?
Yes. Replacement is an ideal time to switch to a variable-speed system for steadier pressure and gentler, longer-lasting motor starts.
Does the well need disinfecting afterward?
Yes. Opening the well can introduce bacteria, so disinfection and follow-up testing are recommended before using the water for drinking.